How to Set Up the Rivian x Kammok Crosswing Awning

Quick answer

To set up the Rivian x Kammok Crosswing Awning, first install the custom mounting kit onto your Rivian Cargo Crossbars, then attach the awning housing to the brackets, and finally deploy the canopy by unrolling it and securing the legs. The entire process takes about 20–30 minutes and requires basic hand tools. Always check that all bolts are tight and the canopy is properly tensioned before use.

What you need before you start

Gather the following: the Crosswing Awning, the custom mounting kit (included), a torque wrench or hex key set, and a step stool if your Rivian is lifted. The mounting kit is designed specifically for Rivian Cargo Crossbars, so no drilling or modification is needed. Work on a flat surface with enough space to open the awning fully.

Step 1: Position the mounting brackets on the crossbars

Slide the two mounting brackets onto your Rivian Cargo Crossbars. The brackets are marked left and right; ensure the angled side faces outward. Loosely tighten the bolts so you can still adjust the position. For a typical setup, center the brackets between the crossbars, but you can shift them forward or backward to balance weight. Checkpoint: The brackets should be parallel to each other and perpendicular to the crossbars.

Step 2: Attach the awning housing to the brackets

With the help of a friend, lift the awning housing and align its mounting channels with the brackets. Slide the housing onto the brackets until it sits flush. Insert the provided bolts and tighten them by hand first, then use a hex key to snug them down. Do not overtighten; the aluminum housing can strip if you force it. Common mistake: Forgetting to use the included washers, which can cause rattling. Checkpoint: The housing should be secure with no side-to-side play.

Step 3: Deploy the canopy

Unlatch the strap that holds the canopy closed. Pull the canopy out and away from the vehicle; the bagless design means it unrolls quickly. Once the canopy is fully extended, locate the two legs at the far end. Extend each leg to the desired height and lock them in place. If the ground is soft, use the included stakes to secure the legs. Checkpoint: The canopy should be taut with no sagging. If it sags, adjust the leg height or re-roll the canopy slightly.

Step 4: Secure and tension the canopy

Attach the guy lines to the loops on the canopy corners and stake them out at a 45-degree angle. This keeps the awning stable in light wind. Use the tensioning buckles to tighten the canopy fabric. Do not over-tension; the fabric should have a slight give. Common mistake: Staking guy lines too close to the vehicle, which can cause the canopy to rub against the paint. Checkpoint: Walk around the awning and ensure no part is touching the vehicle body.

Step 5: Packing up

To pack up, reverse the process: remove stakes and guy lines, collapse the legs, and roll the canopy back toward the housing. The bagless design means you simply roll and latch. Make sure the canopy is dry before rolling to prevent mold. Checkpoint: The latch should click securely. If it doesn't, check for debris in the track.

Step-by-step setup

1. Position brackets on crossbars: Slide the mounting brackets onto your Rivian Cargo Crossbars, ensuring the angled side faces outward. Loosely tighten bolts to allow adjustment. Checkpoint: Brackets are parallel and perpendicular to crossbars.
2. Attach awning housing: With a friend, lift the awning and slide it onto the brackets. Insert and hand-tighten bolts, then snug with a hex key. Do not overtighten. Common mistake: Forgetting washers, which can cause rattling.
3. Deploy canopy: Unlatch the strap, pull the canopy out, and extend the legs to your desired height. Lock legs and stake if needed. Checkpoint: Canopy is taut with no sagging.
4. Secure and tension: Attach guy lines to corner loops and stake at 45 degrees. Use tensioning buckles to tighten fabric slightly. Common mistake: Staking too close to vehicle, risking paint rub.
5. Pack up: Remove stakes and guy lines, collapse legs, and roll canopy back into housing. Latch securely. Checkpoint: Latch clicks; ensure canopy is dry before rolling.

Product facts

• Rivian X Kammok Crosswing Awning: Seamless Rivian Integration: The custom mounting kit locks into Rivian Cargo Crossbars, positioning the awning at the perfect angle while maintaining a sleek, built-in look. No drilling or modifications required, and the awning sits at the ideal angle for shade.
• Rivian X Kammok Crosswing Awning: Durable, Bagless Housing: A bag-free design allows for lightning-fast setup at a moment’s notice, while the tough-as-nails aluminum housing prevents rust for a lifetime of adventure. You save time on setup and pack-up, and the housing withstands weather without rusting.
• Rivian X Kammok Crosswing Awning: UV and Mold Resistant Canopy: Our VeloXTM 600D PVC Coated Polyester fabric is UV and mold resistant. The canopy blocks harmful UV rays and resists mold, so it stays fresh even if packed damp.